ARN Trading Ltd t/a AHR International
Tel +44 (0)1727 738430
Fax +44 (0)1727 899394
AS9120 & ISO9001 Approved

Barden bearing part number system

PrefixSuffixDefinition
(B) JH.CAGE - ANGULAR/C J TYPE: ONE-PIECE MACHINED- BRONZE 80-10-10
(B) JJ.CAGE - ANGULAR/C J TYPE: ONE-PIECE STAMPED- BRONZE, PHOSPHOR
(K)2.RADIAL CLEARANCE - MINIATURES: 0.0001 - 0.0003 INCH RADIAL PLAY
(K)25.RADIAL CLEARANCE - MINIATURES:0.0002- .0005 INCH RADIAL PLAY
(K)3.SPINDLE & TURBINE BEARINGS: TIGHT
(K)3.RADIAL CLEARANCE - MINIATURES:0.0002 - .0004 INCH RADIAL PLAY
(K)5.EXTRA THIN SERIES: 0.0003- 0.0008 INCH
(K)5.TORQUE TUBE BEARING UP TO 2.3125": 0.0005- 0.0011 INCH
(K)5.SPINDLE & TURBINE BEARINGS: NORMAL
(K)5.RADIAL CLEARANCE - MINIATURES:0.0005- .0008 INCH RADIAL PLAY
(K)6.EXTRA THIN SERIES: 0.0005 - .0010 INCH
(K)6.TORQUE TUBE BEARING UP TO 2.3125": 0.0008- .0014 INCH
(K)6.RADIAL CLEARANCE - MINIATURES:0.0008- .0011 INCH RADIAL PLAY
(K}4.RADIAL CLEARANCE - MINIATURES:0.0003- .0005 INCH RADIAL PLAY
(V) (0)-(XX)-A.OIL LUBE PROCEDURE: CENTRIFUGE BEARING 2 MINUTES AT -LOOG AFTER LUBRICATION.
(V) (0)-(XX)-B.OIL LUBE PROCEDURE: CENTRIFUGE BEARING 2 MINUTES AT 400G AFTER LUBRICATION.
(V) (OJ-(XX)-C.OIL LUBE PROCEDURE: CENTRIFUGE BEARING 2 MINUTES AT 200G AFTER LUBRICATION.
(XX) H.DUPLEXING: HEAVY PRELOAD
(XX)L.DUPLEXING: LIGHT PRELOAD
(XX)M.DUPLEXING: MEDIUM PRELOAD ON 1900, 100, 200, AND 300 SERIES BEARINGS ONLY
(XX)S.DUPLEXING: SINGLE BEARING WITH FACES FLUSH
0-(XX)-N.OIL LUBE PROCEDURE: SPECIFIC OIL QUANTITY (N - NO. OF DROPS, NEEDLE SIZE #26)
0-10.OIL LUBRICATION: TERESSO 43
0-11.OIL LUBRICATION: WINSORLUBE L-245X - (MIL-L-6085)
0-12.OIL LUBRICATION: TERESSO V78 .
0-13.OIL LUBRICATION: DOW CORNING 200-20 - (W-D-001078)
0-14.OIL LUBRICATION: ESSO TURBO OIL 2389 - (MIL-L-7808G)
0-15.OIL LUBRICATION: TENNECO L401D - (MIL-L-6085)
0-17.OIL LUBRICATION: G.E. VERSILUBE F-50 - (MIL-S-81087 (I) )
0-18.OIL LUBRICATION: G.E. SF96
0-19.OIL LUBRICATION: G.E. VERSILUBE F44 - (MIL-S-81087 (II) )
0-20.OIL LUBRICATION: DOW CORNING - 710
0-21.OIL LUBRICATION: HERCOFLEX 600
0-22.OIL LUBRICATION: TENNECO L423
0-23.OIL LUBRICATION: DOW CORNING 510-12000
0-24.OIL LUBRICATION: EP PIONEER FLO - (MIL-L-6085)
0-25.OIL LUBRICATION: DOW CORNING 510-50
0-26.OIL LUBRICATION: TERESSO V79
0-27.OIL LUBRICATION: HARDEN 0-26 PLUS ADD.
0-28.OIL LUBRICATION: MOBIL XRL-714
0-29.OIL LUBRICATION: KENDALL KG-80
0-30.OIL LUBRICATION: KENDALL SRG-60
0-31.OIL LUBRICATION: BRAY NPT-3A
0-32.OIL LUBRICATION: MOBIL XRL-743A
0-33.OIL LUBRICATION: DUPONT KRYTOX 143AZ
0-34.OIL LUBRICATION: DUPONT KRYTOX 143AA
0-35.OIL LUBRICATION: DUPONT KRYTOX 143AB
0-36.OIL LUBRICATION: DUPONT KRYTOX 143AC
0-37.OIL LUBRICATION: HARDEN - MOON OIL
0-38.OIL LUBRICATION: HARDEN PRESERVATIVE
0-39.OIL LUBRICATION: KENDALL SRG160
0-9.OIL LUBRICATION: ESSO AVIA. INSTR. OIL - (MIL-L-7870)
A.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED - NYSORB
A.CAGE - ANGULAR/C B TYPE:ONE-PIECE MACHINED CONICAL POCKETS - NYSORB
B.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED— SYNTHANE XX - PAPER BASE
B.CAGE - ANGULAR/C B TYPE:ONE-PIECE MACHINED CONICAL POCKETS - SYNTHANE XX
B.BEARING TYPE: ANGULAR CONTACT - SEPARABLE INNER
D.DUPLEXING: UNIVERSAL DUPLEX PAIR
DB.DUPLEXING: DUPLEX PAIR - BACK-TO-BACK
DBD.DUPLEXING: SINGLE BEARING AND DD SET MOUNTED DB
DBDD.DUPLEXING: DD SET AND DD SET MOUNTED DB
DBDQ.DUPLEXING: DD SET AND DQ SET MOUNTED DB
DBQ.DUPLEXING: SINGLE BEARING AND DQ SET MOUNTED DB
DBQQ.DUPLEXING: DQ SET AND DQ SET MOUNTED DB
DBT.DUPLEXING: SINGLE BEARING AND DT PAIR MOUNTED DB
DBTD.DUPLEXING: TANDEM PAIR AND DD SET MOUNTED DB
DBTQ.DUPLEXING: TANDEM PAIR AND DQ SET MOUNTED DB
DBTT.DUPLEXING: TANDEM PAIR AND TANDEM PAIR MOUNTED DB
DD.DUPLEXING: TRIPLEX SET - TANDEM MOUNT
DF.DUPLEXING: DUPLEX PAIR - FACE-TO-FACE
DQ.DUPLEXING: QUAD SET - TANDEM MOUNT
DT.DUPLEXING: DUPLEX PAIR - TANDEM MOUNT
E.SPECIAL RADIAL RUNOUT (INCHES): I.E. 0.00005, O.R. STANDARD-
E1.SPECIAL RADIAL RUNOUT (INCHES): I.R. 0.00005, O.R. 0.0001
E2.SPECIAL RADIAL RUNOUT (INCHES): I.R. 0.00005, O.R. 0.00005
E3.SPECIAL RADIAL RUNOUT (INCHES): I.R. 0.0001, O.R. STANDARD
E4.SPECIAL RADIAL RUNOUT (INCHES): I.R. 0.0001, O.R. 0.0001
E5.SPECIAL RADIAL RUNOUT (INCHES): I.R. 0.0001, O.R. 0.00005
E6.SPECIAL RADIAL RUNOUT (INCHES): I.R. STANDARD, O.R. 0.0001
E7.SPECIAL RADIAL RUNOUT (INCHES): I.R. STANDARD, O.R. 0.00005
E8.SPECIAL RADIAL RUNOUT (INCHES): I.R. STANDARD, O.R. STANDARD -LOW NON-REPETITIVE RUNOUT
F.CLOSURES:SINGLE AL/FIBER FLEXEAL
F(V) (0) (XX) D.OIL LUBE PROCEDURE: FILM OILED - LIGHT
F15CXX).GREASE LUBE PROCEDURE: FILM GREASE 15 MILLIGRAMS PER SQUARE INCH
F5 (XX).GREASE LUBE PROCEDURE: FILM GREASE 5 MILLIGRAMS PER SQUARE INCH
FF.CLOSURES:TWO AL/FIBER FLEXEALS
FG(XX)B(X-Y MG).GREASE LUBE PROCEDURE: FILM GREASE - SPECIFIC GREASE QUANTITY (X-Y IN MG)
FO- (XX)-(X-Y MG).OIL LUBE PROCEDURE: FILM OILED SPECIFIC QUANTITY - (X-Y MG) .
FO- (XX)B(X-Y MG).OIL LUBE PROCEDURE: FILM OILED - INTERNAL SURFACES ONLY {X-Y MG)
FS.CLOSURES:ONE FLEXEAL, ONE SHIELD
FU.CLOSURES:ONE FLEXEAL - ONE SYNCHROSEAL
FV(XX)-(X-Y MG).OIL LUBE PROCEDURE: FILM OILED NON-METALLIC CAGES AFTER VACUUM IMPREGNATION, (X-Y MG)
G.BEARING TYPE: SPLIT INNER - GOTHIC PROFILE - I.R.
G-(XX) (X-Y CMM).GREASE LUBE PROCEDURE: SPECIFIC GREASE QUANTITY (X-Y IN CMM.)
G-10.GREASE LUBRICATION: DOW CORNING - 44 LIGHT - (MIL-L-15719)
G-12.GREASE LUBRICATION: CHEVRON OIL CO. - BRB *2 - (MIL-G-3545)
G-14.GREASE LUBRICATION: DOW CORNING - 33F, L, M
G-16.GREASE LUBRICATION: AMERICAN SUPERMIL M-40
G-18.GREASE LUBRICATION: TEX UNITEMP 500
G-2.GREASE LUBRICATION: BEACON 325
G-2 3.GREASE LUBRICATION: AEROSHELL *5 - (MIL-G-63545)
G-20.GREASE LUBRICATION: AM. SUPERMIL ASU M100
G-21.GREASE LUBRICATION: G.E. VERSILUBE G-300
G-22.GREASE LUBRICATION: 12 PERCENT G-21; 78 PERCENT 0-17
G-24.GREASE LUBRICATION: SHELL ETR-B
G-27.GREASE LUBRICATION: MPB MINIPURE - (MIL-G-15793)
G-28.GREASE LUBRICATION: ESSO ANDOK B - (MIL-G-18709)
G-29.GREASE LUBRICATION: ESSO ANDOK 260
G-32.GREASE LUBRICATION: AM. SUPERMIL A72832 - (MIL-G-23827)
G-33.GREASE LUBRICATION: MOBIL *28 - (MIL-G-81322)
G-34.GREASE LUBRICATION: DUPONT KRYTOX 240AZ
G-35.GREASE LUBRICATION: DUPONT KRYTOX 240AB - (MIL-G-38220)
G-36.GREASE LUBRICATION: DUPONT KRYTOX 240AC - (MIL-G-27617)
G-37.GREASE LUBRICATION: AMERICAN ASU 31052 - (MIL-G-25013)
G-4.GREASE LUBRICATION: MOBIL BRB LIFETIME - (MIL-L-7711)
G-42.GREASE LUBRICATION: TEXACO REGAL STARFAK 12
G-6.GREASE LUBRICATION: ESSO ANDOK C
G-8.GREASE LUBRICATION: TENNECO L793A
H.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED- POROUS SYNTHANE XX - PAPER BASE
H.CAGE - ANGULAR/C B TYPE:ONE-PIECE MACHINED CONICAL POCKETS - POROUS SYNTHANE
H.BEARING TYPE: ANGULAR CONTACT - RELIEVED OUTER - NON- SEPARABLE
J.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED- SILVER
J.BEARING TYPE: ANGULAR CONTACT - RELIEVED INNER - NON- SEPARABLE
JB.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED- 80-10-10 BRONZE
JJ.CAGE - ANGULAR/C J TYPE: ONE-PIECE STAMPED- BRONZE, PHOSPHOR
JJ.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED- SILVER
L.FUNCTIONAL TEST: LOW VIBRATION TEST - SPECIAL FINISH
M.CAGE - ANGULAR/C B TYPE:ONE-PIECE MACHINED STEPPED POCKETS - SYNTHANE LBB
MG(XX).GREASE LUBE PROCEDURE: FILM GREASE - LOW STARTING TORQUE
MX.BEARING TYPE: DOUBLE ROW, SPECIAL
NA.CAGES - DEEP GROOVE:TWO-PIECE MACHINED - RIVETED LEADED BRONZE
NONE.CAGE - ANGULAR/C H TYPE: ONE-PIECE MACHINED - SYNTHANE LBB - LINEN BASE
NONE.CAGE - ANGULAR/C B TYPE: ONE-PIECE MACHINED STEPPED OR CONICAL POCKETS - SYNTHANE LBB OR XX
O.CAGE - ANGULAR/C B TYPE:ONE-PIECE MACHINED CONICAL POCKETS - DELRIN
PA.CAGES - DEEP GROOVE:"W" TYPE CAGE - TEFLON COATED POCKETS - TIGHTLY CLINCHED
QP.CAGES - DEEP GROOVE:ONE-PIECE SNAP, UNFILLED POLYIMIDE
QW.CAGES - DEEP GROOVE:ONE-PIECE SNAP, FEURALON AW
R.SPECIAL RADIAL RUNOUT (INCHES): MARK HIGH POINT I.R.
R1.SPECIAL RADIAL RUNOUT (INCHES): MARK HIGH POINT O.R.
R2.SPECIAL RADIAL RUNOUT (INCHES): MARK HIGH POINT I.R. AND O.R.
RF.CLOSURES: SINGLE FLEXEAL ON HUB SIDE OF FLANGED O.R. OR O.R. THRUST FACE OF H OR J TYPE
RS.CLOSURES: SINGLE SHIELD ON HUB SIDE OF FLANGED O.R. OR O.R. THRUST FACE OF H OR J TYPE
RU.CLOSURES: SINGLE SYNCHROSEAL ON HUB SIDE OF FLANGED O.R. OR O.R. THRUST FACE OF H OR J TYPE
S.CLOSURES: SINGLE STAINLESS SHIELD
SG-1.GREASE LUBRICATION: ANDERSON SLUSHING GREASE
SG-2.GREASE LUBRICATION: ANDERSON SLUSHING GREASE
SS.CLOSURES:TWO STAINLESS SHIELDS
SU.CLOSURES: ONE SHIELD - ONE SYNCHROSEAL
T.CAGES - DEEP GROOVE: TWO-PIECE RIVETED MACHINE AL/SYNTHANE
TA.CAGES - DEEP GROOVE:ONE-PIECE MACHINED SIDE ASSEMBLED - SYNTHANE
TB.CAGES - DEEP GROOVE:ONE-PIECE MACHINED SIDE ASSEMBLED - BARTEMP (SHIELDED BEARING ONLY)
TQ.CAGES - DEEP GROOVE:ONE-PIECE MACHINED SIDE ASSEMBLED - ACETAL PLASTIC - BALL RETAINED
TQM.CAGES - DEEP GROOVE:ONE-PIECE MOLDED SIDE ASSEMBLED - ACETAL PLASTIC - BALL RETAINED
TQT.CAGES - DEEP GROOVE:ONE-PIECE - ACETAL PLASTIC - INNER RACE RETAINED
TWT.CAGES - DEEP GROOVE:TWO-PIECE RIVETED FEURALON AW
U.CLOSURES:SINGLE CLASS/TEFLON SYNCHROSEAL
UU.CLOSURES:TWO GLASS/TEFLON SYNCHROSEALS
V.FUNCTIONAL TEST: STANDARD PRODUCTION TORQUE REQUIREMENT
V(XX).OIL LUBE PROCEDURE: VAC. IMPREGNATED - NON-METALLIC CAGE
V(XX)G XX.OIL LUBE PROCEDURE: VAC. IMPREGNATE PLUS GREASE
VA.FUNCTIONAL TEST: LOW VIBRATION ROUNDNESS CONTROL
VB.FUNCTIONAL TEST: LOW VIBRATION USN MIL-B-17931C
VK.FUNCTIONAL TEST: LOW STARTING TORQUE
VL.FUNCTIONAL TEST: LOW STARTING AND PEAK RUNNING TORQUE
VM.FUNCTIONAL TEST: LOW PEAK RUNNING TORQUE
VT.FUNCTIONAL TEST: LOW PEAK RUNNING TORQUE WITH TRACES
W.CAGES - DEEP GROOVE:TWO-PIECE STAMPED LIGHT WEIGHT LOOSE CLINCHED STAINLESS
X200.SPECIAL FEATURES: OIL TIGHT SEAL BETWEEN O.K. SHIELD GROOVE AND SHIELD
X201.SPECIAL FEATURES: 52100 BEARINGS STABILIZED FOR 450°F OPERATION
X205.SPECIAL FEATURES: FULL BALL COMPLEMENT H AND J TYPE BEARINGS
X50.SPECIAL FEATURES: INSTRUMENT INCH SERIES WITH SMALL BALLS
X54.SPECIAL FEATURES: INSTRUMENT INCH SERIES, DOUBLE ROW, WITH SMALL BALLS
Z.CAGES - DEEP GROOVE:STAINLESS COIL SPRING SEPARATORS
ZA.CAGES - DEEP GROOVE:TEFLON TUBULAR SLUG BALL SEPARATORS
{K}6.SPINDLE & TURBINE BEARINGS: LOOSE


EXAMPLE

Spindle bearing: 116HDBMEO-14
GROUP123456789101112
116HDBMEO-14

In this case:
Group 1 = nothing present implies (SAE 52100 steel)
Group 2 = Bore 80mm, OD 125 mm, width 22mm, 15 degree contact angle
Group 3 = Angular contact one piece machined phenolic
Group 4 = nothing present implies open bearing
Group 9 = Duplex back to back medium preload.
Group 10 = I.R. radial runout 0.00005 max
Group 12 = MIL-L-7808

Departure
from nominal
bore size
(avg. dia. -
inches)

Departure from nominal o.d. size (average dia. - inches)

No o.d.
calibration

0.0000
to
-0.0001

-0.0001
to
-.0002

-0.0002
to
-.0003

-0.0003
to
-.0004

-0.0004
to
-.0005

-0.0005
to
-.0006

No bore
calibration

 

C01

C02

C03

C04

COS

C06

0.0000 to
-.0001

CIO

Cll

C12

C13

C14

CIS

C16

-0.0001 to
-.0002

C20

C21

C22

C23

C24

C25

C26

-0.0002 to
-.0003

C30

C31

C32

C33

C34

C35

C36

-0.0003 to
-.0004

C40

C41

C42

C43

C44

C45

C46

- BORE AND O.D. CALIBRATION
PACKAGE MARKING - TORQUE TUBE, EXTRA THIN, SPINDLE AND TURBINE BEARINGS

BORE AND P.P. CALIBRATION

PACKAGE MARKING - CALIBRATED - MINIATURE AND INSTRUMENT BEARINGS

Departure
from nominal
bore size
(minimum
diameter
inches)

Departure from nominal O.D. size (maximum diameter - inches)

No O.D.
calibration

0.0000
to
0.0001

-0.0001
to
-.0002

0.00000
to
-.00005

-0.00005
to
-.00010

-0.00010
to
-.00015

-0.00015
to
-.00020

Bearing
designation

 

cox

CO4

No bore cal-
ibration

 

COl

CO 2

COA

COB

COC

COD

0.0000 to
-.0001

CIO

Cll

C12

CIA

C1B

C1C

C1D

-0.0001 to
-.0002

C20

C21

C22

C2A

C2B

C2C

C2D

Bearing
designation

CXO

c

CX4

0.00000 to
-.00005

CAO

CA1

CA2

CAA

CAB

CAC

CAD

-0.00005 to
-.00010

CBO

CBl

CB2

CBA

CBB

CBC

CBD

-0.00010 to
-.00015

CCO

CC1

CC2

CCA

CCB

CCC

CCD

-0.00015 to
-.00020

CDO

GDI

CD2

CDA

CDB

CDC

CDD

Bearing
designation

C40

C4X

C44

Contact us now and let us show you exactly what we can do for you.

© ARN Trading Ltd t/a AHR International 2010 All rights reserved